Home | » Products | » Signal Isolated Converters | » 0-24V to Differential signal isolated converter |
Differential signal/Pulse signal isolated Transmitter
(three input three output)
Features:
>> Differential signal/Pulse signal isolated transmitters
>> Support A, B, and Z three-phase differential simultaneous conversion
>> 3 inputs, 3 outputs, selectable output pulse amplitude
>> No change the original waveform frequency, response speed is over 500KHz
>> Three-isolation :signal input/Power/signal output 3000VDC
>> Power supply: 5V, 12V, 15V or 24V DC single power supply
>> Low cost, high small size, ease of use, reliability
>> Standard DIN35 rail mounting
>> Dimensions: 120 mm x 70 mm x 43mm
>> Industrial Temperature Range: - 45 ~ + 85 ℃
Application:
>> Servo encoder signals to the PLC differential
>> Pulse signal amplification and shaping
>> Ground interference suppression
>> Motor speed monitoring system
>> Speed ​​measurement and alarm
>> Signals without distortion transmission and transmission
Products Listing:
DIN33 IAP – S□ - P□ - O□
Signal input | Power | Signal output | |||
input | code | Power | code | output | code |
|
| 24VDC | P1 | Output level 0-5V | O1 |
Single signal input,peak value(Vp-p):5V | S2 | 12VDC | P2 | Output level 0-12V | O2 |
Single signal input,peak value(Vp-p):12V | S3 | 5VDC | P3 | Output level 0-24V | O3 |
Single signal input,peak value(Vp-p):24V | S4 | 15VDC | P4 | Open collector output | O4 |
5v differential pulse signal | S5 |
|
| Differential signal | O5 |
User-defined | Su |
|
| User-defined | Ou |
Products Samples:
1: Input: Encoder differential signal Power supply: 24V Output: 0-5V level
Type No.: DIN33 IAP-S5-P1-O1
2: Input: Encoder differential signal Power supply: 12V Output: 0-24V level
Type No.: DIN33 IAP-S5-P2-O3
3: Input: 0-5V level Power supply: 24V Output: 0-24V level
Type No.: DIN33 IAP-S2-P1-O3
4: Input: 0-5V level Power supply: 12V Output: open collector
Type No.: DIN33 IAP-S2-P2-O4
6.Input:0-24V Power supply: 24V Output: differential signal
Type No.: DIN33 IAP-S4-P1-O5
General Parameters:
Name | Test Condition | Min. | Type | Max. | Units | ||
Isolation voltage | 1min | 1500 | 3000 |
| VDC | ||
Signal input | Amplitude(Vp-p) |
| 0.2 | 10 | 60 | V | |
Frequency |
| 0 | 10 | 500 | kHz | ||
Input Resistance |
| 10 |
|
| kΩ | ||
Input Current | 5V input |
| 0.45 |
| mA | ||
Signal output | Amplitude(Vp-p) | O1:output level 0-5V |
| 5 |
| V | |
Frequency |
| 0 | 10 | 500 | kHz | ||
Voltage(high level) | O1:output level 0-5V |
| 5 |
| V | ||
Voltage(low level) |
| 0 | 0.05 | V | |||
Current(high level) |
| 2 | 5 | mA | |||
Current(low level) |
| 2 | 8 | mA | |||
voltage | O4: Open collector output |
| 5 | 30 | V | ||
current |
| 3 | 10 | mA | |||
Response time |
|
| 1500 |
| ns | ||
Power supply | voltage | User-defined | 3.3 | 12 | 24 | VDC | |
current | VD=12V |
| 150 |
| mA | ||
Power loss |
|
| 2 |
| W | ||
Operation Temperature |
| -45 |
| 85 | ℃ | ||
Storage Temperature |
| -45 |
| 85 | ℃ | ||
Footprint and wire diagram:
PIN | Name | Description | PIN | Name | Description |
1 | OUT1+ | Signal output 1+ | 11 | GND1 | Signal input Ground |
2 | OUT1- | Signal output 1- | 12 | GND1 | Signal input Ground |
3 | OUT2+ | Signal output 2+ | 13 | NC | No connect |
4 | OUT2- | Signal output 2- | 14 | NC | No connect |
5 | OUT3+ | Signal output 3+ | 15 | IN3- | Signal input 3- |
6 | OUT3- | Signal output 3- | 16 | IN3+ | Signal input 3+ |
7 | NC | No connect | 17 | IN2- | Signal input 2- |
8 | NC | No connect | 18 | IN2+ | Signal input 2+ |
9 | PW+ | Power supply + | 19 | IN1- | Signal input 1- |
10 | GND | Power supply - | 20 | IN1+ | Signal input 1+ |
![]() |
WAYJUN INDUSTRIAL AUTOMATION
All Rights Reserved.(Terms of Use) Developed and Managed by Infocom Network Ltd. |